Sideshow's newly announced Gengar Diorama is a genuinely large piece for a $645 price point, and that size is exactly what makes case shopping for it worth doing carefully rather than assuming any statue-labeled case will fit.
The diorama stands roughly 36.8 cm tall by 23.3 cm wide by 23.7 cm deep, which converts to about 14.5 by 9.2 by 9.3 inches. That height figure in particular is the number that matters most here.
Rather than guessing, it's worth running the actual numbers against EVORETRO's real case lineup before buying anything, the same honest approach worth applying to any premium statue purchase.
Here's what actually comes close, what doesn't, and the honest gap collectors should know about going in.
At roughly 14.5 inches tall, Gengar's lunging pose combined with Gastly hovering above it pushes this piece noticeably taller than a typical single-figure statue in a similar price range. Width and depth, at roughly 9.2 and 9.3 inches, are comfortably within range for several existing EVORETRO cases on their own.
Height is the dimension that disqualifies most options here, not width or depth, which is worth keeping in mind before assuming a case's overall footprint guarantees a fit.
EVORETRO's Lockable Showcase Display Case, in its 36 x 24 x 1.65-inch configuration, and the Lockable Display Case lines at roughly 4 inches of interior depth, are both built as wide, flat vendor and trade-show cases meant to lay cards or slim collectibles under a secure lid. Neither comes close to the roughly 9.3 inches of depth or 14.5 inches of height this diorama actually needs.
These cases solve a genuinely different display problem, flat card and slab storage, and were never built with a multi-character diorama's footprint in mind.
EVORETRO's Acrylic Modular Case in its largest 12 x 12 x 12-inch configuration comfortably clears the diorama's 9.2-inch width and 9.3-inch depth with real room to spare. Height is where it falls short: 12 inches of interior clearance against a piece that stands roughly 14.5 inches tall leaves the diorama about 2.5 inches too tall to actually close the case around it.
That's not a close call that might work out once the real piece arrives, the way a tight few-millimeter margin might. A 2.5-inch shortfall is a genuine mismatch, and buying this case expecting a fit would mean discovering the problem only after the diorama arrives.
None of EVORETRO's current enclosed display cases are tall enough to fully house this diorama. That's worth saying plainly rather than stretching a near-fit into a false recommendation, since a case that doesn't actually close around a piece this size isn't protecting it the way an enclosed case is supposed to.
This is the same principle that applies to any premium statue search: an approximate fit that technically doesn't clear isn't a real fit, even when a case's width and depth look comfortable on paper.
For a piece this size, plain open shelf space is the more honest answer than forcing a case that can't actually close. EVORETRO's own tiered acrylic display stand is worth ruling out here too: it's built around a roughly 14.6 x 8.3 x 6-inch footprint for 6-inch action figures, which is smaller than the diorama's own 9.2 x 9.3-inch base, so it isn't sized to actually hold this piece either, not just the enclosed cases.
An ordinary shelf, with the diorama set directly on it, keeps the statue fully visible from every angle and suits a piece built around multiple characters and an open mist effect better than a sealed box would anyway. Pairing that open shelf spot with a simple dust cover, if dust is the main concern rather than impact protection, is a reasonable middle ground for a piece too tall and wide for any current EVORETRO case or riser.
Before buying any case for a multi-character diorama, check the manufacturer's listed height specifically against a case's interior clearance, not just its overall footprint. Width and depth are usually the easier dimensions for a case to accommodate; height is where a tall, dynamic diorama pose runs into trouble first.
Measuring the actual piece once it arrives, rather than relying on listed dimensions alone, is worth doing before committing to any display option, since manufacturing tolerances can shift a final piece slightly from its announced size.
No, its roughly 14.5-inch height exceeds every current enclosed case's interior clearance.
The Acrylic Modular Case's 12 x 12 x 12-inch configuration, though its height falls about 2.5 inches short.
Plain open shelf space, since EVORETRO's own display stand is also sized for smaller figures, not this diorama's footprint, paired with a dust cover if needed.
Gengar's lunging pose with Gastly hovering above pushes the piece's height well past its width and depth.
A $645 diorama this size deserves a real fit, not a case that's close on paper and wrong once it arrives. For smaller pieces in the same collection that do fit a case, EVORETRO's Acrylic Modular Case remains the closest real option on the market today.
!
