Funko Pop and Pop Mart figures are both vinyl blind-box collectibles, so it's a reasonable instinct to assume a Funko-sized display case will just work for Pop Mart too. Sometimes it genuinely does, but Pop Mart's catalog spans a much wider size range than Funko's fairly consistent 4-inch standard.
This isn't a generic figure-care post. We're specifically checking EVORETRO's existing Funko case family against real Pop Mart dimensions, line by line, rather than repeating general display advice that already applies to Funko.
The short version: standard-size Pop Mart lines fit cleanly, oversized ones don't, and the honest answer depends entirely on which sub-line you're displaying.
Here's the actual measurement comparison, plus which EVORETRO case makes sense for each size tier.
EVORETRO's Acrylic Case Display for Standard 4-Inch Figures runs 19.95 CAD, with an outer footprint of 14.0 x 10.2 x 17.5cm and an inner clearance of 13.0 x 9.2 x 16.5cm. That inner height, 16.5cm, is the number that matters most for fitting a standing figure plus its base.
EVORETRO's six-figure acrylic case, built for six standard 4-inch boxes at once, runs 30.00 CAD and is sized the same way per compartment. Both cases were engineered around Funko's roughly 10.16cm standard figure height, which happens to land close to several Pop Mart lines.
Skullpanda's confirmed figure height across recent series, including September 2026's Where Time Dwells line, is 9 to 10cm. That's close enough to the Funko case's 16.5cm inner clearance and 9.2cm inner width that a Skullpanda figure fits with real room to spare rather than a forced squeeze.
This is the cleanest fit in this entire comparison. If your Pop Mart shelf is mostly Skullpanda, the standard 4-inch Funko case is a legitimately good, not just approximate, choice.
A standard Labubu figure runs close to 10cm tall including its signature pointed ears, putting it in the same size range as Skullpanda. The same Funko-sized case that works for Skullpanda should comfortably hold a standard Labubu figure too.
Where this breaks down is the word standard. Labubu specifically has a MEGA format line that scales up dramatically, and that's where a Funko case stops being an option entirely.
Pop Mart's MEGA Labubu figures run far outside Funko territory, with the 400% size measuring roughly 29 to 35cm tall and the 1000% size reaching about 70cm. Neither comes close to fitting inside a case built around a 16.5cm inner height.
CRYBABY's plush formats add a different complication: soft material doesn't hold a fixed silhouette the way rigid vinyl does, and Pop Mart's upcoming Crying Round n Round plush series hasn't published dimensions at all as of this writing. Don't assume a Funko-sized case fits a plush CRYBABY figure just because earlier vinyl CRYBABY releases might have.
For anything in the MEGA tier or an unconfirmed plush format, EVORETRO's acrylic modular case is the better starting point, since its largest configuration opens up to roughly 30.5cm per side with no fixed slot shape forcing one figure size. That still won't fit a 1000% MEGA Labubu, but it comfortably covers most 400% pieces and anything smaller.
EVORETRO's stackable collectible display box with magnetic closure is worth knowing about too, though we'll be straight about it: its published spec sheet lists an inner height that doesn't fully reconcile with its own outer dimensions, so treat its exact clearance as approximate rather than a guaranteed fit for a specific figure until you've checked it against your own piece.
The one-line rule that avoids most of this confusion: measure your actual figure's height, including any base or stand, before matching it to a case's inner clearance number rather than its outer dimensions. Outer measurements look more impressive on a spec sheet but tell you nothing about what actually fits inside.
If a figure runs within roughly a centimeter of a case's inner height, you have workable room; much closer than that and packaging foam or a display base can push it over the edge.
Yes, Skullpanda's 9-10cm height fits comfortably inside the case's 16.5cm inner clearance.
Yes, standard Labubu runs close to 10cm, similar to Skullpanda's size range.
No, MEGA figures run 29cm to 70cm tall, far beyond any Funko-sized case.
EVORETRO's acrylic modular case in its largest configuration, though even that won't fit the 1000% size.
No, plush dimensions haven't been published for the newest series, so don't assume a fit.
A case that fits Skullpanda perfectly can still be the wrong choice for a MEGA Labubu sitting one shelf over. Start with EVORETRO's acrylic case display for standard 4-inch figures for anything in Pop Mart's standard size range, and size up only once your figures actually need it.
!
